If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#11
|
|||
|
|||
Mounting lenses upside down, the result
On 28 Sep 2016 05:59:50 GMT, Sandman wrote:
In article , Bill W wrote: Sandman: In january I posted about my idea to mount lenses upside down on shelves: Sandman Mounting lenses upside down 01/05/2016 "So, strange subject line aside - I'm looking for a way to store my lenses, and I've been thinking about wall-mounting them. I think it actually might look quite cool." And I thought I'd share the end result: https://www.instagram.com/p/BKx_luqAioO I bought some 40+ Nikon rear lens caps and some 20+ sony lens caps, and used polyurethane glue to fix them to the underside after routing some round "pockets" for them so they're inset in the wood. The glue is super strong and I couldn't pry one off no matter how hard I tried. I'm really pleased with the end result! I still think you're crazy. I understand that even if they do fall, they don't necessarily fall far, but still. And glue deteriorates. Strong today, mush tomorrow. You'll be lying in bed when you hear the first one fall. Consider that a cry for help for the others. Polyurethane glue creates a bond that is stronger than both the wood and the plastic, though. Do you know what those lens caps are made of? Most glues, including what you used, will not adhere properly to certain types of plastic. I've learned that the hard way, but my hard way did not involve many thousands of dollars worth of lenses. I admit that it all looks nice, and it's an interesting way to organize things, but I never trust glue when its failure can cost lots of money. If you would have run screws through the caps, you would at least have some warning if the glue failed, but I understand that there might not have been enough clearance between the lens and the screw. Of course, it might last forever. I'm just one of those worst-case guys. |
#12
|
|||
|
|||
Mounting lenses upside down, the result
In article ,
Bill W wrote: On 28 Sep 2016 05:59:50 GMT, Sandman wrote: In article , Bill W wrote: Sandman: In january I posted about my idea to mount lenses upside down on shelves: Sandman Mounting lenses upside down 01/05/2016 "So, strange subject line aside - I'm looking for a way to store my lenses, and I've been thinking about wall-mounting them. I think it actually might look quite cool." And I thought I'd share the end result: https://www.instagram.com/p/BKx_luqAioO I bought some 40+ Nikon rear lens caps and some 20+ sony lens caps, and used polyurethane glue to fix them to the underside after routing some round "pockets" for them so they're inset in the wood. The glue is super strong and I couldn't pry one off no matter how hard I tried. I'm really pleased with the end result! I still think you're crazy. I understand that even if they do fall, they don't necessarily fall far, but still. And glue deteriorates. Strong today, mush tomorrow. You'll be lying in bed when you hear the first one fall. Consider that a cry for help for the others. Polyurethane glue creates a bond that is stronger than both the wood and the plastic, though. Do you know what those lens caps are made of? Most glues, including what you used, will not adhere properly to certain types of plastic. I've learned that the hard way, but my hard way did not involve many thousands of dollars worth of lenses. Those are his $$$$ and he ain't always nice ;-ppp I admit that it all looks nice, and it's an interesting way to organize things, but I never trust glue when its failure can cost lots of money. Modern airplane wings and such are often glued together. Don't tell Mort! If you would have run screws through the caps, you would at least have some warning if the glue failed, but I understand that there might not have been enough clearance between the lens and the screw. Multiple screws close to the perimeter could perhaps secure the cap together with the glue? Of course, it might last forever. I'm just one of those worst-case guys. We want you're kind in the war room! http://www.mathsisfun.com/geometry/perimeter.html -- teleportation kills |
#13
|
|||
|
|||
Mounting lenses upside down, the result
In article , Bill W wrote:
Sandman: In january I posted about my idea to mount lenses upside down on shelves: Sandman Mounting lenses upside down 01/05/2016 "So, strange subject line aside - I'm looking for a way to store my lenses, and I've been thinking about wall-mounting them. I think it actually might look quite cool." And I thought I'd share the end result: https://www.instagram.com/p/BKx_luqAioO I bought some 40+ Nikon rear lens caps and some 20+ sony lens caps, and used polyurethane glue to fix them to the underside after routing some round "pockets" for them so they're inset in the wood. The glue is super strong and I couldn't pry one off no matter how hard I tried. I'm really pleased with the end result! Bill W: I still think you're crazy. I understand that even if they do fall, they don't necessarily fall far, but still. And glue deteriorates. Strong today, mush tomorrow. You'll be lying in bed when you hear the first one fall. Consider that a cry for help for the others. Sandman: Polyurethane glue creates a bond that is stronger than both the wood and the plastic, though. Do you know what those lens caps are made of? Most glues, including what you used, will not adhere properly to certain types of plastic. I've learned that the hard way, but my hard way did not involve many thousands of dollars worth of lenses. I admit that it all looks nice, and it's an interesting way to organize things, but I never trust glue when its failure can cost lots of money. If you would have run screws through the caps, you would at least have some warning if the glue failed, but I understand that there might not have been enough clearance between the lens and the screw. The bottom shelf has screws as well, since the heaviest lenses hang from it. -- Sandman |
#14
|
|||
|
|||
Mounting lenses upside down, the result
In article ,
Sandman wrote: In article , Bill W wrote: Sandman: In january I posted about my idea to mount lenses upside down on shelves: Sandman Mounting lenses upside down 01/05/2016 "So, strange subject line aside - I'm looking for a way to store my lenses, and I've been thinking about wall-mounting them. I think it actually might look quite cool." And I thought I'd share the end result: https://www.instagram.com/p/BKx_luqAioO I bought some 40+ Nikon rear lens caps and some 20+ sony lens caps, and used polyurethane glue to fix them to the underside after routing some round "pockets" for them so they're inset in the wood. The glue is super strong and I couldn't pry one off no matter how hard I tried. I'm really pleased with the end result! Bill W: I still think you're crazy. I understand that even if they do fall, they don't necessarily fall far, but still. And glue deteriorates. Strong today, mush tomorrow. You'll be lying in bed when you hear the first one fall. Consider that a cry for help for the others. Sandman: Polyurethane glue creates a bond that is stronger than both the wood and the plastic, though. Do you know what those lens caps are made of? Most glues, including what you used, will not adhere properly to certain types of plastic. I've learned that the hard way, but my hard way did not involve many thousands of dollars worth of lenses. I admit that it all looks nice, and it's an interesting way to organize things, but I never trust glue when its failure can cost lots of money. If you would have run screws through the caps, you would at least have some warning if the glue failed, but I understand that there might not have been enough clearance between the lens and the screw. The bottom shelf has screws as well, since the heaviest lenses hang from it. The caps to the shelf or the shelf to the console? -- teleportation kills |
#15
|
|||
|
|||
Mounting lenses upside down, the result
On 9/29/2016 2:24 AM, Sandman wrote:
In article , Bill W wrote: Sandman: In january I posted about my idea to mount lenses upside down on shelves: Sandman Mounting lenses upside down 01/05/2016 "So, strange subject line aside - I'm looking for a way to store my lenses, and I've been thinking about wall-mounting them. I think it actually might look quite cool." And I thought I'd share the end result: https://www.instagram.com/p/BKx_luqAioO I bought some 40+ Nikon rear lens caps and some 20+ sony lens caps, and used polyurethane glue to fix them to the underside after routing some round "pockets" for them so they're inset in the wood. The glue is super strong and I couldn't pry one off no matter how hard I tried. I'm really pleased with the end result! Bill W: I still think you're crazy. I understand that even if they do fall, they don't necessarily fall far, but still. And glue deteriorates. Strong today, mush tomorrow. You'll be lying in bed when you hear the first one fall. Consider that a cry for help for the others. Sandman: Polyurethane glue creates a bond that is stronger than both the wood and the plastic, though. Do you know what those lens caps are made of? Most glues, including what you used, will not adhere properly to certain types of plastic. I've learned that the hard way, but my hard way did not involve many thousands of dollars worth of lenses. I admit that it all looks nice, and it's an interesting way to organize things, but I never trust glue when its failure can cost lots of money. If you would have run screws through the caps, you would at least have some warning if the glue failed, but I understand that there might not have been enough clearance between the lens and the screw. The bottom shelf has screws as well, since the heaviest lenses hang from it. Do you think that plastic rear lens cap is made to support the weight of one of those big, heavy lenses? Even though the cap may be screwed and glued to the shelf, that would not keep the cap from eventually breaking from the weight of the lens. I wouldn't depend on a lightweight plastic cap supporting the weight of one of my heavier lenses. |
#16
|
|||
|
|||
Mounting lenses upside down, the result
In article , PAS wrote:
On 9/29/2016 2:24 AM, Sandman wrote: In article , Bill W wrote: Sandman: In january I posted about my idea to mount lenses upside down on shelves: Sandman Mounting lenses upside down 01/05/2016 "So, strange subject line aside - I'm looking for a way to store my lenses, and I've been thinking about wall-mounting them. I think it actually might look quite cool." And I thought I'd share the end result: https://www.instagram.com/p/BKx_luqAioO I bought some 40+ Nikon rear lens caps and some 20+ sony lens caps, and used polyurethane glue to fix them to the underside after routing some round "pockets" for them so they're inset in the wood. The glue is super strong and I couldn't pry one off no matter how hard I tried. I'm really pleased with the end result! Bill W: I still think you're crazy. I understand that even if they do fall, they don't necessarily fall far, but still. And glue deteriorates. Strong today, mush tomorrow. You'll be lying in bed when you hear the first one fall. Consider that a cry for help for the others. Sandman: Polyurethane glue creates a bond that is stronger than both the wood and the plastic, though. Do you know what those lens caps are made of? Most glues, including what you used, will not adhere properly to certain types of plastic. I've learned that the hard way, but my hard way did not involve many thousands of dollars worth of lenses. I admit that it all looks nice, and it's an interesting way to organize things, but I never trust glue when its failure can cost lots of money. If you would have run screws through the caps, you would at least have some warning if the glue failed, but I understand that there might not have been enough clearance between the lens and the screw. The bottom shelf has screws as well, since the heaviest lenses hang from it. Do you think that plastic rear lens cap is made to support the weight of one of those big, heavy lenses? Even though the cap may be screwed and glued to the shelf, that would not keep the cap from eventually breaking from the weight of the lens. I wouldn't depend on a lightweight plastic cap supporting the weight of one of my heavier lenses. $ure he does! He's from c.o.l.a, you know... ;-ppp -- teleportation kills |
#17
|
|||
|
|||
Mounting lenses upside down, the result
On 29/09/2016 14:07, PAS wrote:
[] Do you think that plastic rear lens cap is made to support the weight of one of those big, heavy lenses? Even though the cap may be screwed and glued to the shelf, that would not keep the cap from eventually breaking from the weight of the lens. I wouldn't depend on a lightweight plastic cap supporting the weight of one of my heavier lenses. Perhaps those shelves could be turned the other way up? -- Cheers, David Web: http://www.satsignal.eu |
#18
|
|||
|
|||
Mounting lenses upside down, the result
In article ,
David Taylor wrote: On 29/09/2016 14:07, PAS wrote: [] Do you think that plastic rear lens cap is made to support the weight of one of those big, heavy lenses? Even though the cap may be screwed and glued to the shelf, that would not keep the cap from eventually breaking from the weight of the lens. I wouldn't depend on a lightweight plastic cap supporting the weight of one of my heavier lenses. Perhaps those shelves could be turned the other way up? Perhaps he could sell it to a chapie down under. Erik??? -- teleportation kills |
#19
|
|||
|
|||
Mounting lenses upside down, the result
On Thu, 29 Sep 2016 09:07:10 -0400, PAS wrote:
On 9/29/2016 2:24 AM, Sandman wrote: In article , Bill W wrote: Sandman: In january I posted about my idea to mount lenses upside down on shelves: Sandman Mounting lenses upside down 01/05/2016 "So, strange subject line aside - I'm looking for a way to store my lenses, and I've been thinking about wall-mounting them. I think it actually might look quite cool." And I thought I'd share the end result: https://www.instagram.com/p/BKx_luqAioO I bought some 40+ Nikon rear lens caps and some 20+ sony lens caps, and used polyurethane glue to fix them to the underside after routing some round "pockets" for them so they're inset in the wood. The glue is super strong and I couldn't pry one off no matter how hard I tried. I'm really pleased with the end result! Bill W: I still think you're crazy. I understand that even if they do fall, they don't necessarily fall far, but still. And glue deteriorates. Strong today, mush tomorrow. You'll be lying in bed when you hear the first one fall. Consider that a cry for help for the others. Sandman: Polyurethane glue creates a bond that is stronger than both the wood and the plastic, though. Do you know what those lens caps are made of? Most glues, including what you used, will not adhere properly to certain types of plastic. I've learned that the hard way, but my hard way did not involve many thousands of dollars worth of lenses. I admit that it all looks nice, and it's an interesting way to organize things, but I never trust glue when its failure can cost lots of money. If you would have run screws through the caps, you would at least have some warning if the glue failed, but I understand that there might not have been enough clearance between the lens and the screw. The bottom shelf has screws as well, since the heaviest lenses hang from it. Do you think that plastic rear lens cap is made to support the weight of one of those big, heavy lenses? Even though the cap may be screwed and glued to the shelf, that would not keep the cap from eventually breaking from the weight of the lens. I wouldn't depend on a lightweight plastic cap supporting the weight of one of my heavier lenses. Good point. Nearly all plastics (and wood) have a long-term strength which is only a fraction (typically 10%~40%) of their short term strength. Cracks will normally start to develop before the final failure. -- Regards, Eric Stevens |
#20
|
|||
|
|||
Mounting lenses upside down, the result
In article , PAS wrote:
Sandman: The bottom shelf has screws as well, since the heaviest lenses hang from it. Do you think that plastic rear lens cap is made to support the weight of one of those big, heavy lenses? Even though the cap may be screwed and glued to the shelf, that would not keep the cap from eventually breaking from the weight of the lens. I wouldn't depend on a lightweight plastic cap supporting the weight of one of my heavier lenses. Well, to each his own. These caps are quite sturdy, and the only force when hanging is down. Now, if they were mounted to stick out to the side, maybe I'd agree with you, because that sideway pressure on only part of the plastic tabs might make it break over time. -- Sandman |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Mounting lenses upside down | Sandman | Digital Photography | 20 | January 6th 16 01:41 PM |
Plastic cameras and the danger of mounting heavy lenses | SteveG | Digital Photography | 3 | July 23rd 09 06:11 PM |
Plastic cameras and the danger of mounting heavy lenses | SteveG | Digital SLR Cameras | 3 | July 23rd 09 06:11 PM |
Plastic cameras and the danger of mounting heavy lenses | D. Peter Maus | Digital Photography | 0 | July 21st 09 08:36 PM |
Plastic cameras and the danger of mounting heavy lenses | Eric Stevens | Digital SLR Cameras | 1 | July 20th 09 02:46 AM |