If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
Heat absorbing glass or one-size-fits all glass carrier for 23CII negative popping problem
Hi,
I just spent the better part of yesterday trying to print from a 35mm negative in my Beseler 23CII. I had already noticed some focusing problems with this print but had attributed it to the negative itself. After a rather long and involved burning and dodging sequence (I'm still recovering from it), I noticed when I removed the negative from the carrier that it had sort of protruded a bit through the carrier. It was rather striking. I gather that this is the infamous "negative popping" problem that has attracted much discussion on this group (see for example http://groups.google.com/groups?hl=e...com%26rnum%3D2). I am in some ways relieved to have an explanation, because I had been going crazy figuring out why I had to constantly refocus for _every_ exposure. It also explains why the focus never seemed quite right. So here are my questions. First, does the Beseler "heat absorbing glass" (Beseler # 8042) occupy the space in the filter drawer where the filter frame itself goes? If so, how would I use my VC filters? Having shelled out some odd $20 for those filters, I am loathe to have to buy below-the-lens filters. Second, can anyone share their experience in using Beseler universal glass negative carriers (either the plain 8074 or anti-Newton 8072)? I find this option very intriguing for a couple of reasons. I plan to start doing medium format sometime in the not-to-distant future, and have limited space in my closet darkroom. The idea of having a one-size-fits all carrier appeals to me. Also, my reading of the archvies on this topic is that a glass carrier is the only sure-fire solution to the popping problem because even with the heat-absorbing glass the problem occurs. There was one post that went so far as to say that, even without popping, any unevenness in the negative results in loss of sharpness. If so, this is a compelling argument. I am resigned to living with having to clean the extra surfaces. If I were to go for the glass negative carrier option, is the anti-Newton carrier worth the extra money? Are there other solutions to Newton rings? Finally, since it's going to take me a bit of time to make this decision and/or convince my wife of why I'm spending more for an enlarger accessory than I spent for the enlarger itself, I am looking for interim solutions. One suggestion I saw was to tightly tape the negative to the carrier so as to stretch it out. Any other ideas? Thanks! --Phil |
#2
|
|||
|
|||
Heat absorbing glass or one-size-fits all glass carrier for 23CII negative popping problem
Phil Glaser wrote:
So here are my questions. First, does the Beseler "heat absorbing glass" (Beseler # 8042) occupy the space in the filter drawer where the filter frame itself goes? If so, how would I use my VC filters? Having shelled out some odd $20 for those filters, I am loathe to have to buy below-the-lens filters. On top of the glass? My bigger Beseler has a sheet of glass put into the filter slot. That way the filter doesn't fall down the hole-) Obviously it helps to keep things dust free. Or pretty close to it. Second, can anyone share their experience in using Beseler universal glass negative carriers (either the plain 8074 or anti-Newton 8072)? I find this option very intriguing for a couple of reasons. I plan to Looking at the pictures this is just a normal glass carrier. It's the max size your enlarger will take. I've use a 4x5 one masked off for smaller formats. Or for strips of negatives. If you're willing to make up some simple masks [mat board nothing fancy needed] then it works fine. start doing medium format sometime in the not-to-distant future, and have limited space in my closet darkroom. The idea of having a one-size-fits all carrier appeals to me. Also, my reading of the archvies on this topic is that a glass carrier is the only sure-fire solution to the popping problem because even with the heat-absorbing I think the design of the enlarger must play into how much heat is created. I don't get any popping with any sort of carrier. It's not because I'm doing anything special so it must be the enlarger. Finally, since it's going to take me a bit of time to make this decision and/or convince my wife of why I'm spending more for an enlarger accessory than I spent for the enlarger itself, I am looking for interim solutions. One suggestion I saw was to tightly tape the negative to the carrier so as to stretch it out. Any other ideas? Buy it used. Maybe consider the negtrans [I think that's the name]. It pulls the negative taut. Also buy it used. Buy some thick glass from the glass shop and slip it into the enlarger. Maybe that will cut the heat down enough. Wait until the negative pops before you focus. Pick which ever one works for you. Nick |
#3
|
|||
|
|||
Heat absorbing glass or one-size-fits all glass carrier for 23CII negative popping problem
Negatrans is just a transport mechanism, does a little better holding negs
flat that the standard carrier since the edges are in intimate contact with the rubber drive band. Beseler also makes (made) a Negaflat for 4x5, great for holding 4x5 negs flat but very format specific (originally made for film pack?) and could tear up the edges of your 4x5 negatives. -- darkroommike ---------- "Nick Zentena" wrote in message ... Phil Glaser wrote: So here are my questions. First, does the Beseler "heat absorbing glass" (Beseler # 8042) occupy the space in the filter drawer where the filter frame itself goes? If so, how would I use my VC filters? Having shelled out some odd $20 for those filters, I am loathe to have to buy below-the-lens filters. On top of the glass? My bigger Beseler has a sheet of glass put into the filter slot. That way the filter doesn't fall down the hole-) Obviously it helps to keep things dust free. Or pretty close to it. Second, can anyone share their experience in using Beseler universal glass negative carriers (either the plain 8074 or anti-Newton 8072)? I find this option very intriguing for a couple of reasons. I plan to Looking at the pictures this is just a normal glass carrier. It's the max size your enlarger will take. I've use a 4x5 one masked off for smaller formats. Or for strips of negatives. If you're willing to make up some simple masks [mat board nothing fancy needed] then it works fine. start doing medium format sometime in the not-to-distant future, and have limited space in my closet darkroom. The idea of having a one-size-fits all carrier appeals to me. Also, my reading of the archvies on this topic is that a glass carrier is the only sure-fire solution to the popping problem because even with the heat-absorbing I think the design of the enlarger must play into how much heat is created. I don't get any popping with any sort of carrier. It's not because I'm doing anything special so it must be the enlarger. Finally, since it's going to take me a bit of time to make this decision and/or convince my wife of why I'm spending more for an enlarger accessory than I spent for the enlarger itself, I am looking for interim solutions. One suggestion I saw was to tightly tape the negative to the carrier so as to stretch it out. Any other ideas? Buy it used. Maybe consider the negtrans [I think that's the name]. It pulls the negative taut. Also buy it used. Buy some thick glass from the glass shop and slip it into the enlarger. Maybe that will cut the heat down enough. Wait until the negative pops before you focus. Pick which ever one works for you. Nick |
Thread Tools | |
Display Modes | |
|
|