If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
*%$@#*&^%$!!!!!!!!!!!
Well, you've seen the post with a link to my first photo, which was very
much out of focus and (I think) overexposed. This evening, I had almost exactly the same conditions as far as weather and light and clouds etc, so out I went with my camera, spent about 20 minutes working with the focus, tilt and swing. I even wore my glasses, and used a magnifier to see the ground glass. When I was done, you could read the license plate numbers on the trucks!!! I put in the film holder, pulled out the dark slide, snapped the picture and went to put the dark slide back in - NO GO!! Aaarrrg! I'm going to try removing the dark slide (from as far as it went back in) and removing the negative in the dark room this evening and then I'm going to develop it, but I'm preparing myself for major disappointment :-( . I guess I'll have to be more careful how I load the holder, although I can't understand how I got the dark slide into the holder in the first place when I was loading. :'( -- regards from :: John Bartley 43 Norway Spruce Street Stittsville, Ontario Canada, K2S1P5 ( If you slow down it takes longer - does that apply to life also?) |
#2
|
|||
|
|||
*%$@#*&^%$!!!!!!!!!!!
In article , John Bartley
wrote: Well, you've seen the post with a link to my first photo, which was very much out of focus and (I think) overexposed. This evening, I had almost exactly the same conditions as far as weather and light and clouds etc, so out I went with my camera, spent about 20 minutes working with the focus, tilt and swing. I even wore my glasses, and used a magnifier to see the ground glass. When I was done, you could read the license plate numbers on the trucks!!! I put in the film holder, pulled out the dark slide, snapped the picture and went to put the dark slide back in - NO GO!! Aaarrrg! [...] John, what you experienced is pretty common with new LF users. You accidently loaded the film so that it slid down the rails right under the dark slide. As you discovered, once out of the holder, the film pops up and blocks the slide. Next time when you load the film feel free to use both hands to feel the film down from the very top, then down the narrow retaining rails. Once the film is in, you should be able to only bend/lift the very upper left (notch) corner of the film. Not to worry. We've all been there! |
#3
|
|||
|
|||
*!!! - whoohoo!
one_of_many wrote:
John, what you experienced is pretty common with new LF users. You accidently loaded the film so that it slid down the rails right under the dark slide. As you discovered, once out of the holder, the film pops up and blocks the slide. Next time when you load the film feel free to use both hands to feel the film down from the very top, then down the narrow retaining rails. Once the film is in, you should be able to only bend/lift the very upper left (notch) corner of the film. Not to worry. We've all been there! I have an image - yippee!! It's hanging to dry now, so I should know soon - anticipation is so stressfull :-D !! -- regards from :: John Bartley 43 Norway Spruce Street Stittsville, Ontario Canada, K2S1P5 ( If you slow down it takes longer - does that apply to life also?) |
#4
|
|||
|
|||
*!!! - If at first...
John Bartley wrote:
I have an image - yippee!! It's hanging to dry now, so I should know soon - anticipation is so stressfull :-D !! Well.....it was a pretty poor image. The developing went well (I think), but the picture is way too bright, which leads me to think that my antiquated light meter (an old Seconic Aires) is giving me false readings. The picture is also blurry, and this time I know without a doubt that it was in focus everywhere on the ground glass so the only conlusion that I can draw is that I'm getting motion in the camera/tripod assembly when I release the shutter. http://www3.sympatico.ca/oldrad/Photo/ My course of action will be 1) obtain a more solid tripod 2) take better care in loading the holders 3) waste a few negatives experimenting with the "sunny F/16" rule while I research and obtain a new meter So....all in all, it was a fun and positive result from what was looking like a complete waste of time at the beginning cheers all! -- regards from :: John Bartley 43 Norway Spruce Street Stittsville, Ontario Canada, K2S1P5 ( If you slow down it takes longer - does that apply to life also?) |
#5
|
|||
|
|||
*!!! - If at first...
On Thu, 01 Jul 2004 07:26:10 -0400, John Bartley
wrote: John Bartley wrote: I have an image - yippee!! It's hanging to dry now, so I should know soon - anticipation is so stressfull :-D !! Well.....it was a pretty poor image. The developing went well (I think), but the picture is way too bright, which leads me to think that my antiquated light meter (an old Seconic Aires) is giving me false readings. The picture is also blurry, and this time I know without a doubt that it was in focus everywhere on the ground glass so the only conlusion that I can draw is that I'm getting motion in the camera/tripod assembly when I release the shutter. http://www3.sympatico.ca/oldrad/Photo/ My course of action will be 1) obtain a more solid tripod 2) take better care in loading the holders 3) waste a few negatives experimenting with the "sunny F/16" rule while I research and obtain a new meter So....all in all, it was a fun and positive result from what was looking like a complete waste of time at the beginning Most any old manual or semi-auto camera (film or digital) should provide you with a useable light meter. By definition, any camera that can't provide this function for you would be a point & shoot. rafe b. http://www.terrapinphoto.com |
#6
|
|||
|
|||
*%$@#*&^%$!!!!!!!!!!!
John Bartley said:
I put in the film holder, pulled out the dark slide, snapped the picture and went to put the dark slide back in - NO GO!! Aaarrrg! You presumably loaded the film in the rails upon which the dark slide moves up and down rather than below those rails which is where the film is supposed to go. This used to happen to me all the time because it's very easy to do and is extremely frustrating. Fortunately there is an easy way to prevent it. In daylight pull the darkslide of an empty holder up a couple inches. Look at the interior of the holder, at the base where the flap is. It will be very obvious that there are rails upon which the darkslide slides up and down and that the film is supposed to go under the bottom of the two rails. The bottom rail on each side of the holder has a sharp corner (at least all of mine do, some new, some ancient). When you're actually loading film, after you've got the film in the holder just rub your finger in the area where those two corners are located and see if you can feel the corners with your finger. If you can then the film is loaded properly. If you can't what you will feel instead is the film resting on top of the corner. If that's the case then you have the film in the dark slide rails and you need to remove it and start over (no, touching the film with your finger won't create a smudge or otherwise hurt the film). This is one of those things that takes five minutes to describe in writing and maybe five seconds max to actually do but hopefully this is clear. Of course you could also pull the dark slide out of the holder entirely and then see if it will go back in after you've loaded the film but that's an unnecessary pain to do in the dark and gets to be time consuming if you're loading many sheets of film "John Bartley" wrote in message ... Well, you've seen the post with a link to my first photo, which was very much out of focus and (I think) overexposed. This evening, I had almost exactly the same conditions as far as weather and light and clouds etc, so out I went with my camera, spent about 20 minutes working with the focus, tilt and swing. I even wore my glasses, and used a magnifier to see the ground glass. When I was done, you could read the license plate numbers on the trucks!!! I put in the film holder, pulled out the dark slide, snapped the picture and went to put the dark slide back in - NO GO!! Aaarrrg! I'm going to try removing the dark slide (from as far as it went back in) and removing the negative in the dark room this evening and then I'm going to develop it, but I'm preparing myself for major disappointment :-( . I guess I'll have to be more careful how I load the holder, although I can't understand how I got the dark slide into the holder in the first place when I was loading. :'( -- regards from :: John Bartley 43 Norway Spruce Street Stittsville, Ontario Canada, K2S1P5 ( If you slow down it takes longer - does that apply to life also?) |
#7
|
|||
|
|||
*%$@#*&^%$!!!!!!!!!!!
Vladamir30 wrote:
John Bartley said: I put in the film holder, pulled out the dark slide, snapped the picture and went to put the dark slide back in - NO GO!! Aaarrrg! You presumably loaded the film in the rails upon which the dark slide moves up and down rather than below those rails which is where the film is supposed to go. This used to happen to me all the time because it's very easy to do and is extremely frustrating. Fortunately there is an easy way to prevent it. In daylight pull the darkslide of an empty holder up a couple inches. Look at the interior of the holder, at the base where the flap is. It will be very obvious that there are rails upon which the darkslide slides up and down and that the film is supposed to go under the bottom of the two rails. The bottom rail on each side of the holder has a sharp corner (at least all of mine do, some new, some ancient). When you're actually loading film, after you've got the film in the holder just rub your finger in the area where those two corners are located and see if you can feel the corners with your finger. If you can then the film is loaded properly. If you can't what you will feel instead is the film resting on top of the corner. If that's the case then you have the film in the dark slide rails and you need to remove it and start over (no, touching the film with your finger won't create a smudge or otherwise hurt the film). This is one of those things that takes five minutes to describe in writing and maybe five seconds max to actually do but hopefully this is clear. When I load sheet film, I have a much easier way of determining if I accidently loaded the film in the darkslide slot: Before even trying to reinsert the dark slide, I flip the bottom flap into the position it will need to go. If it does not go in flush with the rest of the holder when pressing very gently, I know already that I goofed and just reload the sheet. Forcing the darkslide in will at least scratch the film, and who needs that! -- .~. Jean-David Beyer Registered Linux User 85642. /V\ Registered Machine 241939. /( )\ Shrewsbury, New Jersey http://counter.li.org ^^-^^ 09:25:00 up 3 days, 16:54, 3 users, load average: 0.02, 0.08, 0.21 |
#8
|
|||
|
|||
*%$@#*&^%$!!!!!!!!!!!
Jean-David Beyer said:
When I load sheet film, I have a much easier way of determining if I accidently loaded the film in the darkslide slot: Before even trying to reinsert the dark slide, I flip the bottom flap into the position it will need to go. If it does not go in flush with the rest of the holder when pressing very gently, I know already that I goofed and just reload the sheet. Forcing the darkslide in will at least scratch the film, and who needs that! I think you must have misunderstood my suggestion. I didn't suggest that the dark slide be forced in. After inserting the film and before sliding the dark slide into place I suggested just touching the two corners of the rail and with your finger and that will tell you whether the film is loaded properly or not. Nothing is being forced into anything. It sounds like you remove the dark slide entirely from the holder when loading film since you speak of "reinserting" it. I don't do that, I just pull the dark slide about half way up when loading film rather than removing it entirely from the holder. I guess some of us find some things easier than others but it doesn't seem to me that removing and replacing the dark slide with each sheet of film being loaded and then checking how the flap fits is "much easier" than leaving the dark slide in the holder and just touching two corners of the rail with your finger. And of course it's possible for the flap to fit flush with the rest of the holder even if the film is imporperly loaded. I actually would think the give away of improper loading if you remove the dark slide entirely wouldn't be how the flap fits but rather would be the difficulty encountered in putting the dark slide back in the holder with the film in the dark slide slots. But perhaps I don't follow exactly what you're doing and even if I do, to each his or her own, whatever works for you, etc. etc. "Jean-David Beyer" wrote in message ... Vladamir30 wrote: John Bartley said: I put in the film holder, pulled out the dark slide, snapped the picture and went to put the dark slide back in - NO GO!! Aaarrrg! You presumably loaded the film in the rails upon which the dark slide moves up and down rather than below those rails which is where the film is supposed to go. This used to happen to me all the time because it's very easy to do and is extremely frustrating. Fortunately there is an easy way to prevent it. In daylight pull the darkslide of an empty holder up a couple inches. Look at the interior of the holder, at the base where the flap is. It will be very obvious that there are rails upon which the darkslide slides up and down and that the film is supposed to go under the bottom of the two rails. The bottom rail on each side of the holder has a sharp corner (at least all of mine do, some new, some ancient). When you're actually loading film, after you've got the film in the holder just rub your finger in the area where those two corners are located and see if you can feel the corners with your finger. If you can then the film is loaded properly. If you can't what you will feel instead is the film resting on top of the corner. If that's the case then you have the film in the dark slide rails and you need to remove it and start over (no, touching the film with your finger won't create a smudge or otherwise hurt the film). This is one of those things that takes five minutes to describe in writing and maybe five seconds max to actually do but hopefully this is clear. When I load sheet film, I have a much easier way of determining if I accidently loaded the film in the darkslide slot: Before even trying to reinsert the dark slide, I flip the bottom flap into the position it will need to go. If it does not go in flush with the rest of the holder when pressing very gently, I know already that I goofed and just reload the sheet. Forcing the darkslide in will at least scratch the film, and who needs that! -- .~. Jean-David Beyer Registered Linux User 85642. /V\ Registered Machine 241939. /( )\ Shrewsbury, New Jersey http://counter.li.org ^^-^^ 09:25:00 up 3 days, 16:54, 3 users, load average: 0.02, 0.08, 0.21 |
#9
|
|||
|
|||
*%$@#*&^%$!!!!!!!!!!!
Vladamir30 wrote:
Jean-David Beyer said: When I load sheet film, I have a much easier way of determining if I accidently loaded the film in the darkslide slot: Before even trying to reinsert the dark slide, I flip the bottom flap into the position it will need to go. If it does not go in flush with the rest of the holder when pressing very gently, I know already that I goofed and just reload the sheet. Forcing the darkslide in will at least scratch the film, and who needs that! I think you must have misunderstood my suggestion. I didn't suggest that the dark slide be forced in. After inserting the film and before sliding the dark slide into place I suggested just touching the two corners of the rail and with your finger and that will tell you whether the film is loaded properly or not. Nothing is being forced into anything. It sounds like you remove the dark slide entirely from the holder when loading film since you speak of "reinserting" it. I don't do that, I just pull the dark slide about half way up when loading film rather than removing it entirely from the holder. I guess some of us find some things easier than others but it doesn't seem to me that removing and replacing the dark slide with each sheet of film being loaded and then checking how the flap fits is "much easier" than leaving the dark slide in the holder and just touching two corners of the rail with your finger. And of course it's possible for the flap to fit flush with the rest of the holder even if the film is imporperly loaded. I have never found that to be the case. I use Lisco holders, in case that matters. I actually would think the give away of improper loading if you remove the dark slide entirely wouldn't be how the flap fits but rather would be the difficulty encountered in putting the dark slide back in the holder with the film in the dark slide slots. But perhaps I don't follow exactly what you're doing and even if I do, to each his or her own, whatever works for you, etc. etc. I have to remove the dark slide all the way sometime, because after exposing it, I must put it in the other way to indicate it is exposed. Then after processing, I must reverse it again to indicate it is unexposed. It just so happens that that is when I do it. -- .~. Jean-David Beyer Registered Linux User 85642. /V\ Registered Machine 241939. /( )\ Shrewsbury, New Jersey http://counter.li.org ^^-^^ 12:25:00 up 3 days, 19:54, 6 users, load average: 0.13, 0.12, 0.07 |
#10
|
|||
|
|||
*%$@#*&^%$!!!!!!!!!!!
Jean-David Beyer wrote:
Vladamir30 wrote: Right about now, I would like to sincerely thank ALL for their input. I have read all the replies, both on the group and in private email, and have appreciated and am grateful for ALL the input. From each reply I am able to extract a bit of information about how each contributors unique method is similar or different to what I've been doing, and to see how their ways may be adapted to my own skill level (or lack there-of :-) ). I have already made progress this way, so to ALL, a huge and hearty THANK YOU !! ps : it's the differences in us that make it so interesting so see how we each solve our particular challanges. I'm looking forward to more challenges :-) ! -- regards from :: John Bartley 43 Norway Spruce Street Stittsville, Ontario Canada, K2S1P5 ( If you slow down it takes longer - does that apply to life also?) |
Thread Tools | |
Display Modes | |
|
|