If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
Why pixel peeping (usually) makes no sense
There's a great difference between screen resolution (72-96 PPI) and
good printing, where rules of thumb for normal viewing distances are at least 130 DPI for barely acceptable results, and up to 230 DPI for excellent results. With current technology, anything more than 300 DPI is pretty much wasted. This translates to: 4x6 5x7 8x10 11x14 16x20 20x30 ------ ------ ------ ------ ------ ------ Acceptable: 0.4MP 0.6MP 1.4MP 2.6MP 5 MP 10 MP Very good: 0.8MP 1.1MP 2.6MP 5 MP 10 MP 19 MP Excellent: 1.3MP 1.9MP 4 MP 8 MP 16 MP 32 MP Best: 2.2MP 3.2MP 7 MP 14 MP 28 MP 54 MP For my 7.2MP Panasonic FZ8, 11x14 is "excellent" at about 216 DPI. The same effect on my high-quality 96 PPI display is 96 / 216 = 44% zoom, more realistically 50% zoom. On a standard 72 PPI display it's 72 / 216 = 33%. Even these reduced zooms exaggerate the issue, since display pixels are so much bigger and more distinct than high-resolution print dots. For this reason display zoom needs to be reduced even further for meaningful print judging, to about 25-33% (depending on display) for a high-quality (8MP) 11x14 print. Because screen pixels are so much larger and coarser than good printing dots (effectively a magnifier), zooming in more than this doesn't make sense (unless the ultimate objective is screen display of 100% crop rather than normal screen display or printing). If you can't see an issue at this reduced display zoom, then you're not going to see it in an excellent print either. Thus my normal practice is to assess images on screen at no more than 33% zoom, zooming in farther only to examine the effectiveness of sharpening and/or noise reduction. This relationship does of course change for larger print sizes, but then print degradation due to pixelation becomes an offsetting issue -- more pixels are needed to make larger high-quality prints. When I anticipate printing larger than 11x14 with my 7.2MP Panasonic FZ8, I shoot multiple overlapping images and then stitch them together, multiple-frame super-resolution. 4 image stitching is sufficient for excellent 16x20 and very good 20x30 prints, and even larger sizes can be produced by stitching more images. In which case the same reduced zoom is appropriate. -- Best regards, John Navas Panasonic DMC-FZ8 (and several others) |
#2
|
|||
|
|||
Why pixel peeping (usually) makes no sense
In article ,
John Navas wrote: This is a nice paper, and you put a lot of work into it. You did not have much to say about cropping, however. One of the attractions of digital photography is the ease of post- processing (compared to using a darkroom!). When I take pictures, my first priority is to get the shutter button pushed quickly. I can take care of composition in Photoshop or Thumbs Plus. I admit, I have no idea how other folks frame their shots. But in my case, higher pixel counts are useful. By the way, what is this "print" that you speak of? Is it related to darkroom techniques and stiff paper? I don't mess with that stuff any more. Do you? -- David Arnstein (00) {{ }} ^^ |
#3
|
|||
|
|||
Why pixel peeping (usually) makes no sense
Two points you didn't take into consideration is what about cropping images
post process and also it's very difficult stitch photos with moving subjects. In addition to this, stitching adds to post process time and if you want a certain perspective in the photo (very wide angle/fisheye), stitching won't work. I don't like cropping images myself and do my cropping in the view finder, however there are times when it is not possible to get the crop you want in camera (for example if you want a square image, you can't physically get closer to the subject, you make a mistake with composition, etc), so more pixels are always better as long as the pixel pitch isn't too small, as it can increase noise. Of course, I know where you're coming from and I'm happy with my 20D, which is 8MP. PS: From a commercial point of view, certain clients require photo's to be a minimum of XYZ MB TIFF. "John Navas" wrote in message ... There's a great difference between screen resolution (72-96 PPI) and good printing, where rules of thumb for normal viewing distances are at least 130 DPI for barely acceptable results, and up to 230 DPI for excellent results. With current technology, anything more than 300 DPI is pretty much wasted. This translates to: 4x6 5x7 8x10 11x14 16x20 20x30 ------ ------ ------ ------ ------ ------ Acceptable: 0.4MP 0.6MP 1.4MP 2.6MP 5 MP 10 MP Very good: 0.8MP 1.1MP 2.6MP 5 MP 10 MP 19 MP Excellent: 1.3MP 1.9MP 4 MP 8 MP 16 MP 32 MP Best: 2.2MP 3.2MP 7 MP 14 MP 28 MP 54 MP For my 7.2MP Panasonic FZ8, 11x14 is "excellent" at about 216 DPI. The same effect on my high-quality 96 PPI display is 96 / 216 = 44% zoom, more realistically 50% zoom. On a standard 72 PPI display it's 72 / 216 = 33%. Even these reduced zooms exaggerate the issue, since display pixels are so much bigger and more distinct than high-resolution print dots. For this reason display zoom needs to be reduced even further for meaningful print judging, to about 25-33% (depending on display) for a high-quality (8MP) 11x14 print. Because screen pixels are so much larger and coarser than good printing dots (effectively a magnifier), zooming in more than this doesn't make sense (unless the ultimate objective is screen display of 100% crop rather than normal screen display or printing). If you can't see an issue at this reduced display zoom, then you're not going to see it in an excellent print either. Thus my normal practice is to assess images on screen at no more than 33% zoom, zooming in farther only to examine the effectiveness of sharpening and/or noise reduction. This relationship does of course change for larger print sizes, but then print degradation due to pixelation becomes an offsetting issue -- more pixels are needed to make larger high-quality prints. When I anticipate printing larger than 11x14 with my 7.2MP Panasonic FZ8, I shoot multiple overlapping images and then stitch them together, multiple-frame super-resolution. 4 image stitching is sufficient for excellent 16x20 and very good 20x30 prints, and even larger sizes can be produced by stitching more images. In which case the same reduced zoom is appropriate. -- Best regards, John Navas Panasonic DMC-FZ8 (and several others) |
#4
|
|||
|
|||
Why pixel peeping (usually) makes no sense
Scott W wrote:
Shoot, hit the wrong button and send a blank replay, sorry about that. Once your message appears in Thunderbird, select it, right click, select cancel message, and if you've been quick enough you'll get the message deleted from the news server before it propagates. OTOH if you're not quick enough, you can end up deleting it from your news server after it's propagated, and end up with replies to messages that you thought you didn't send. |
#5
|
|||
|
|||
Why pixel peeping (usually) makes no sense
|
#6
|
|||
|
|||
Why pixel peeping (usually) makes no sense
On Fri, 16 Nov 2007 08:49:35 -1000, Scott W wrote
in : John Navas wrote: [SNIP] Well I don't see how looking at the screen at %25-33% can tell you how the print is going to look, unless you are making a very small print. Say you start with 8MP and view at 25%, you effectively are throwing out 15 out of 16 pixels in your viewing, reducing your 8MP image down to 0.5 MP. Viewing at 100% on screen would only be comparable to printing if your screen had the same high resolution as the printer, but it's not even close, as I tried to explain. I also would take some issue with your table of needed pixels, this is a personal thing. For an 8 x 10 print I would say 4MP is acceptable, but just and very good would be 8MP. And with a good printer you can see a noticeable improvement going from 8 to 16 MP for a 8 x 10 print, so I don't see how even 8MP could be call best for this size print. A lot depends on the printer used, when I use Costco they can't seem to use detail much past 200 ppi, maybe a bit past but not close to 300ppi. With my cheap inkjet printer I can see detail to 400ppi. Assuming your Costco uses the Fuji Frontier on Crystal Archive paper (or something comparable), and assuming it's properly adjusted, then print quality at 300 DPI should be comparable to your inkjet printer at any DPI. The reason cheap inkjets need more DPI is that they don't do as good a job of reproducing a given DPI. (PPI pertains to screen, not printing.) The other thing that I have noted is over time I have found uses for higher resolution photos, part of this is making bigger prints and part of this is doing slide shows that have pan and zooms in them. I look forward to the day that I can have a 4 x 6 foot wall mounted display that has 200 ppi, that is going to take close to 140MP, and for it to really look clean you need to down size a bit, so you might want to start out at 200MP. As I wrote, I stitch multiple images together when I need higher resolution. The point is you can never have too much resolution and your images can never look too clean. Maybe not for how you are using today, but what about 20 years from now? You can likewise never have too much money and be too skinny. I'm talking what's real and practical. -- Best regards, John Navas Panasonic DMC-FZ8 (and several others) |
#7
|
|||
|
|||
Why pixel peeping (usually) makes no sense
On Fri, 16 Nov 2007 19:13:37 GMT, "Ali" wrote in
: Two points you didn't take into consideration is what about cropping images post process and also it's very difficult stitch photos with moving subjects. True, although the best current stitching software may be better than you think at removing ghosts. (I commented on cropping earlier in the thread.) In addition to this, stitching adds to post process time and if you want a certain perspective in the photo (very wide angle/fisheye), stitching won't work. Actually it will -- the best stitching software easily produces multiple different projections. PS: From a commercial point of view, certain clients require photo's to be a minimum of XYZ MB TIFF. True, but I've not (yet) seen any that wouldn't accept what I can get right out of camera for other than mural prints. -- Best regards, John Navas Panasonic DMC-FZ8 (and several others) |
#8
|
|||
|
|||
Why pixel peeping (usually) makes no sense
Hi John,
"John Navas" wrote in message ... There's a great difference between screen resolution (72-96 PPI) and good printing, where rules of thumb for normal viewing distances are at least 130 DPI for barely acceptable results, and up to 230 DPI for excellent results. I don't know what distance you're viewing the prints from, but 230dpi doesn't cut it for a anything smaller than a 22.5x15 print viewed at *normal* viewing distances (as established by Kodak's reasearch - see "Handbook of Image Quality", ISBN-10: 0824707702, ISBN-13: 9780824707705). And you're not going to get that kind of pixel density from a 7.2Mp camera. The best such a camera can give, without degrading the image by interpolation, is about a 7x10.5 print, for which you need around 288dpi. With current technology, anything more than 300 DPI is pretty much wasted. This translates to: 4x6 5x7 8x10 11x14 16x20 20x30 ------ ------ ------ ------ ------ ------ Acceptable: 0.4MP 0.6MP 1.4MP 2.6MP 5 MP 10 MP Very good: 0.8MP 1.1MP 2.6MP 5 MP 10 MP 19 MP Excellent: 1.3MP 1.9MP 4 MP 8 MP 16 MP 32 MP Best: 2.2MP 3.2MP 7 MP 14 MP 28 MP 54 MP Your assumption that print densities would remain the same regardless of print size is wrong unless you're one of those sods who insists that everything has to be viewed from some arbitrary fixed distance. For a: .. 4x6 print, you'd want about 360ppi .. 5x7 print, you'd want 300-360ppi .. 8x10 or 11x14 print, you'd want about 288ppi .. 16x20 print, you'd want about 240ppi .. 20x30 print, you'd want about 200ppi prefereably uninterpolated, for view at *normal* viewing distances and assuming the CoC for the required visual resolution matches the human eye's diffraction limits (ie about 90 arc-seconds for a 3mm pupil) under normally-lit indoor conditions. By what standard do you define 'acceptable', 'very good', excellent', 'best'? For my 7.2MP Panasonic FZ8, 11x14 is "excellent" at about 216 DPI. The same effect on my high-quality 96 PPI display is 96 / 216 = 44% zoom, more realistically 50% zoom. On a standard 72 PPI display it's 72 / 216 = 33%. Hmm, for viewing at *normal* viewing distances (about 18 inches for am 11x14 print), that implies a CoC with an angular resolution of about 105-110 arc-seconds. That seems to imply that the 90 arc-seconds I used for the above calculations is better than that - your 'best', perhaps. Even these reduced zooms exaggerate the issue, since display pixels are so much bigger and more distinct than high-resolution print dots. For this reason display zoom needs to be reduced even further for meaningful print judging, to about 25-33% (depending on display) for a high-quality (8MP) 11x14 print. Because screen pixels are so much larger and coarser than good printing dots (effectively a magnifier), zooming in more than this doesn't make sense (unless the ultimate objective is screen display of 100% crop rather than normal screen display or printing). If you can't see an issue at this reduced display zoom, then you're not going to see it in an excellent print either. Thus my normal practice is to assess images on screen at no more than 33% zoom, zooming in farther only to examine the effectiveness of sharpening and/or noise reduction. This relationship does of course change for larger print sizes, but then print degradation due to pixelation becomes an offsetting issue -- more pixels are needed to make larger high-quality prints. When I anticipate printing larger than 11x14 with my 7.2MP Panasonic FZ8, I shoot multiple overlapping images and then stitch them together, multiple-frame super-resolution. 4 image stitching is sufficient for excellent 16x20 and very good 20x30 prints, and even larger sizes can be produced by stitching more images. In which case the same reduced zoom is appropriate. 'Pixel peeping', as you put it, is useful if you want to be able to edit the image to maximise its qualities. Even with your FZ8, a 1024x768 screen is going to downsample by a factor of 10, which really limits your ability to work with fine detail unless you zoom in. Of course, if you're limited to a camera that only outputs jpeg files, you don't have much as scope there as you get a decent DSLR anyway (even one with less pixels). Cheers -- cmyk |
#9
|
|||
|
|||
Why pixel peeping (usually) makes no sense
For my 7.2MP Panasonic FZ8, 11x14 is "excellent" at about 216 DPI.
To produce an 11x14 print without interpolation from your FZ8, you can only print at 200ppi. Printing at 216dpi is only going to degrade the image through interpolation. You can see what's optimum by dividing the print dimensions by the available number of pixels. That gives an angular resolution of around 115 arc-seconds. Cheers -- cmyk |
#10
|
|||
|
|||
Why pixel peeping (usually) makes no sense
Mmm. I'm not talking about ghosts. I am talking about shooting moving
subjects, whether it maybe a F1 car or people. I also can't see how stitching software is able to create the same effect as a fisheye lens with multiple images, without a lot of time spent in post production. "John Navas" wrote in message ... Two points you didn't take into consideration is what about cropping images post process and also it's very difficult stitch photos with moving subjects. True, although the best current stitching software may be better than you think at removing ghosts. (I commented on cropping earlier in the thread.) In addition to this, stitching adds to post process time and if you want a certain perspective in the photo (very wide angle/fisheye), stitching won't work. Actually it will -- the best stitching software easily produces multiple different projections. |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
For some people film makes more sense | Graham Fountain | 35mm Photo Equipment | 60 | December 26th 06 10:02 AM |
Olympus E-400 grip makes way more sense | RichA | Digital SLR Cameras | 0 | December 3rd 06 01:01 AM |
Wide Angle IS makes sense... | MarkČ | Digital Photography | 84 | September 9th 06 01:42 PM |
Wide angle IS makes sense... | MarkČ | Digital SLR Cameras | 9 | September 3rd 06 01:26 PM |
Hopefully this makes sense | HeritageMom | Digital Photography | 20 | February 9th 06 07:08 PM |