A Photography forum. PhotoBanter.com

If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below.

Go Back   Home » PhotoBanter.com forum » Photo Equipment » Other Photographic Equipment
Site Map Home Register Authors List Search Today's Posts Mark Forums Read Web Partners

Flash will work on film camera but not digital?



 
 
Thread Tools Display Modes
  #1  
Old April 16th 12, 07:16 AM posted to rec.photo.digital.point+shoot,rec.photo.equipment.misc,rec.photo.digital
DaveC[_4_]
external usenet poster
 
Posts: 18
Default Flash will work on film camera but not digital?

Is there any reason an "economy" flash (Achiever 630AF) will work on a film
camera but not on a digital camera. I've been told this but see no reason for
it to be so.

The destination camera is Canon PowerShot G9.

Thanks.

  #3  
Old April 17th 12, 12:13 AM posted to rec.photo.digital.point+shoot,rec.photo.equipment.misc,rec.photo.digital
Fred McKenzie
external usenet poster
 
Posts: 214
Default Flash will work on film camera but not digital?

In article
,
DaveC wrote:

Is there any reason an "economy" flash (Achiever 630AF) will work on a film
camera but not on a digital camera. I've been told this but see no reason for
it to be so.

The destination camera is Canon PowerShot G9.



As mentioned by J. and Ryan, some older flashes were directly fired by a
mechanical switch contact in the camera. They may have too high an
open-circuit voltage or short-circuit current for use with cameras that
fire the flash electronically.

If you do a web search for that specific flash, you may find
specifications for it. It might have been sold as being compatible with
a particular camera. If it claims to be compatible with Canon EOS
cameras, it probably would work with the G9.

What if it is safe to use, but does not communicate with the G9's
electronics? If the flash is claimed to be "automatic", you can
manually set your camera's f/stop according to a calculator on the flash
body.

You also might be able to use it in completely manual mode. Set the
camera's shutter speed to something less than the maximum flash sync
speed. Then calculate the camera's f/stop based on the flash guide
number, camera ISO setting and the distance from flash to subject. The
flash may have a calculator for that too.

Fred
  #4  
Old April 17th 12, 01:21 AM posted to rec.photo.digital.point+shoot,rec.photo.equipment.misc,rec.photo.digital
nospam
external usenet poster
 
Posts: 24,165
Default Flash will work on film camera but not digital?

In article
, DaveC
wrote:

Is there any reason an "economy" flash (Achiever 630AF) will work on a film
camera but not on a digital camera. I've been told this but see no reason for
it to be so.

The destination camera is Canon PowerShot G9.


if it's designed for a film camera it probably has an older and no
longer used ttl system and that won't work with newer cameras.

you may be able to get it to work if it has a fully manual mode or an
automatic mode where the sensor on the camera adjusts the flash, no ttl
at all.
  #5  
Old April 17th 12, 05:40 PM posted to rec.photo.digital.point+shoot,rec.photo.equipment.misc,rec.photo.digital
Wolfgang Weisselberg
external usenet poster
 
Posts: 5,285
Default Flash will work on film camera but not digital?

DaveC wrote:
Is there any reason an "economy" flash (Achiever 630AF) will work on a film
camera but not on a digital camera.


Yep.
Apart from the voltage on the contacts:
- the flash may depend on OTF-TTF (Off the film, through the
lens) metering. Sensors reflect very different from film,
so metering *during* the flash is not supported: there
needs to be a pre-shot metering flash.

- If the flash was designed and built before the protocols
for telling the flash "flash only a small flash" and "now
fire a 1/4 flash" etc. were designed, the flash wouldn't
know how to talk to the camera nor understand the camera
(nor have the smartness to stop the flash on it's own).

- Since the flash doesn't know how to properly talk to the
camera, it'll only work on
- full power only
- manual control (if available)
- "computer flash" with manually set aperture (basically the
flash detects how much light has been reflected and shuts
off based on that and the aperture) --- if available.

None of that is what most people expect from a flash (to
'just work' usually) ...

The destination camera is Canon PowerShot G9.


If the voltage is OK and you're willing to understand and really
*work* for the flash shots getting right, you should be fine.

If the flash is a "computer flash" with inbuild sensor, and you
fix your aperture, you might be able to be happy even with snap
shooting with little restrictions.

But if you want comfort and automatics, that's not really the
flash you want.

-Wolfgang
 




Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is Off
HTML code is Off
Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
What's a Good Digital Camera for Time-Lapse Work? Nic[_2_] Digital Photography 0 October 11th 07 02:56 PM
Film Flash in Digital Camera. Just Shoot Me Digital SLR Cameras 4 September 20th 07 05:04 PM
2D-3D digital camera software doesn't work for us..any suggestions? [email protected] Digital Photography 0 January 18th 07 03:36 AM
Which digital camera will work underwater ??? Oliver Wen Digital Photography 13 December 15th 05 06:19 PM


All times are GMT +1. The time now is 02:27 PM.


Powered by vBulletin® Version 3.6.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright ©2004-2024 PhotoBanter.com.
The comments are property of their posters.