If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
sheet film developing is hard
Step by step instructions on tray developing are on our web site
www.viewcamera.com in the Free Articles section steve simmons |
#2
|
|||
|
|||
Have you tried to use JOBO 4x5 tank? I used other tank as you mentioned
before. It was very difficult. But the JOBO one is really good and easy to use. I bought mine via eBay. "PGG" ??? newsan.2004.09.29.04.39.14.715000@NO_SP_A_Myahoo .com ???... I've gone through my first 25-sheet pack of film. I've figured out how to operate my view camera just fine. I can take a decent picture-- exposing and focusing properly. But I had no idea how difficult developing it is...I thought that would be the easy part first 5 sheets I fumbled around with a color processing tube that didn't work out due to the film not staying flat against the tube next 3-5 sheets I tried using my own PVC tubes. They leaked all over the place and I got uneven development next 10 sheets I tray developed. At least these were evenly developed but all scratched up. Plus I fumbled around in the dark spilling crap all over the floor. My most recent attempts have been with 2 BZTS tubes bought on eBay. The best so far. But I realized that 3 of my favorite shots are messed up because, for about 10-20 seconds, the tubes were not moving. Yep...uneven development even though total time was 8 minutes. Sigh.... Frustrated but I haven't quite given up yet. |
#3
|
|||
|
|||
PGG wrote:
I've gone through my first 25-sheet pack of film. I've figured out how to operate my view camera just fine. I can take a decent picture-- exposing and focusing properly. But I had no idea how difficult developing it is...I thought that would be the easy part first 5 sheets I fumbled around with a color processing tube that didn't work out due to the film not staying flat against the tube next 3-5 sheets I tried using my own PVC tubes. They leaked all over the place and I got uneven development next 10 sheets I tray developed. At least these were evenly developed but all scratched up. Plus I fumbled around in the dark spilling crap all over the floor. My most recent attempts have been with 2 BZTS tubes bought on eBay. The best so far. But I realized that 3 of my favorite shots are messed up because, for about 10-20 seconds, the tubes were not moving. Yep...uneven development even though total time was 8 minutes. Sigh.... Frustrated but I haven't quite given up yet. Tray developing is IMHO the easiest and best way to develop sheet film. You may have occasional failures--I've scratched the film on very rare occasions, but generally, it's dead easy. Here's my method; I'm sure there are others: I have three 5X7 trays with water in them--labeled respectively N, N+1, N+2. Next to them, I have four 8X10 trays, Developer, Water stop, Fix,Water rinse. When all these are set up in a row in my sink, I arrange my holders with all N's in one stack, all N+1's in another, and any N+2's in another. (I rarely have any N+2's.) Then, IN THE DARK, I unload all the holders and place the films in their respective water baths. This is one spot to exercise care--put each film in the water bath and fully submerge it for a few seconds before putting the next one in on top of it. I've worked out a method of using only the tip of my little finger to push the film down into the water, since then my other fingers remain dry to unload the rest of the film. This is an important step because wetting each film separately like this prevents them from sticking together. Then, setting my Gralab for the longest time I need (N+2 or N+1 if I have any designated for those times), I pick up the whole stack of, e.g., N+2 films, from the water bath and place them in the developer, emulsion side down. I then begin shuffling them top to bottom at a slow and steady rate. As the timer clicks down to N+1 time, I bring those sheets in the developer, add them to the N+2's and keep shuffling. Likewise, when the timer gets to the N time, I bring the N's in. (CAVEAT: I have occasionally attempted to develop as many as 8 sheets at once, but I don't recommend it. Six is probably the maximum you should develop in one stack. So if you have 1 N+2 and 4 N+1's and 5 N's, then do the N+'s in one run and the N's in another.) While shuffling, take care not to let the corners of the film you're shuffling gouge the films underneath. When end of development time comes, move the whole stack to the water bath and shuffle through once or twice. Then to the fixer, where the shuffling continues. At some point about two minutes into the fixer shuffle, though Fred Picker would not have approved, you can turn on the lights and see if your film is fully cleared. If not, keep shuffling until it is and go a little longer to be sure of complete fixing. Then, in the light, you can move it to the water rinse for another shuffle or two. Dump the water off and replace with your Perma-wash or whatever other hypo-clearing agent you're using (which you've mixed in a beaker ahead of time so you can just pour it into the tray.) Shuffle the films for the recommended time. Then dump, and do whatever you do for washing. When wash is complete, add a drop or two of Photo-Flo to your final wash water, and then hang each of the sheets up with a clothes pin by a corner on a line over your sink to dry. This method has worked successfully for many years for me, and saved me a lot of money on tanks, etc. Hope you like it. Larry |
#4
|
|||
|
|||
But I had no idea how difficult developing it
is. The Nikor adjustable stainless steel daylight developing tank is the ticket. Holds 12 sheets of 4x5 film and about 40 ounces of chemicals. You load your film in the dark onto a special cage, stick it in the tank, cap it and turn on the lights! Proceed to develop as you would 35mm film in a SS tank, inverting the tank for agitation, etcetera. Hard to get but it does come up on eBay every now and then. Will set you back over $100 but you'll never regret it. Bob G |
#5
|
|||
|
|||
PGG wrote:
I've gone through my first 25-sheet pack of film. I've figured out how to operate my view camera just fine. I can take a decent picture-- exposing and focusing properly. But I had no idea how difficult developing it is...I thought that would be the easy part If you're willing to spend the money Jobo makes a couple of different systems. You don't even need a processor. Nick |
#6
|
|||
|
|||
PGG wrote:
I've gone through my first 25-sheet pack of film. I've figured out how to operate my view camera just fine. I can take a decent picture-- exposing and focusing properly. But I had no idea how difficult developing it is...I thought that would be the easy part If you're willing to spend the money Jobo makes a couple of different systems. You don't even need a processor. Nick |
#7
|
|||
|
|||
"PGG" wrote
Sigh.... Frustrated but I haven't quite given up yet. That's the way to do it: keep at it until you give up completely. It's sort of the whole point of life. -- Nicholas O. Lindan, Cleveland, Ohio Consulting Engineer: Electronics; Informatics; Photonics. Remove spaces etc. to reply: n o lindan at net com dot com psst.. want to buy an f-stop timer? nolindan.com/da/fstop/ |
#8
|
|||
|
|||
"PGG" wrote
Sigh.... Frustrated but I haven't quite given up yet. That's the way to do it: keep at it until you give up completely. It's sort of the whole point of life. -- Nicholas O. Lindan, Cleveland, Ohio Consulting Engineer: Electronics; Informatics; Photonics. Remove spaces etc. to reply: n o lindan at net com dot com psst.. want to buy an f-stop timer? nolindan.com/da/fstop/ |
#10
|
|||
|
|||
"Bob G" wrote in message
... But I had no idea how difficult developing it is. The Nikor adjustable stainless steel daylight developing tank is the ticket. Holds 12 sheets of 4x5 film and about 40 ounces of chemicals. You load your film in the dark onto a special cage, stick it in the tank, cap it and turn on the lights! You forgot the clip. |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Cut Film Development | ATIPPETT | In The Darkroom | 3 | June 23rd 04 11:15 PM |
Insane new TSA rule for film inspection | [email protected] | 35mm Photo Equipment | 94 | June 23rd 04 05:17 AM |
WTB : sheet film holder | John Bartley | Large Format Photography Equipment | 2 | June 4th 04 11:11 PM |
Sheet film developing | Serge Korolev | In The Darkroom | 11 | April 16th 04 09:01 AM |
FA: NIKON LS-4500AF HiEnd LargeFormatFilm Scanner | bleanne | Other Photographic Equipment | 1 | November 27th 03 07:34 AM |