If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
|
Thread Tools | Display Modes |
#11
|
|||
|
|||
Enlarger Bellows Rebuild - modern tricks?
The Bellows is done, and without a single reference to any help. It is
actually pretty obvious how to make it so. It sure is much easier working with big bellows than small ones. |
#12
|
|||
|
|||
Enlarger Bellows Rebuild - modern tricks?
In article ,
John wrote: Materials technology has changed a great deal in the past few decades, so I am hoping (L-A-Z-Y) that there might be a flexible, nonsticky, spray-on coating that can be applied inside and outside a large bellows (for 10X10" enlarger). Spray-on, no. But Permatex Ultra Black gasket maker (available at your local auto parts store) works well, though it does not leave a smooth interior surface. It is rubbery, not sticky, once it dries. I use a small piece of black gaffer's tape on the outside to make a backing, then Ultra Black on the inside. Remove the tape backing, or not, after the gasket maker dries, according to your preference. -- Thor Lancelot Simon "The inconsistency is startling, though admittedly, if consistency is to be abandoned or transcended, there is no problem." - Noam Chomsky |
#13
|
|||
|
|||
Enlarger Bellows Rebuild - modern tricks?
"Thor Lancelot Simon" wrote in message ... Spray-on, no. But Permatex Ultra Black gasket maker (available at your local auto parts store) works well, though it does not leave a smooth interior surface. It is rubbery, not sticky, once it dries. *SLAPing my head* I used that stuff when building cars. (Never on a carburator, however. Baaaad there.) I use a small piece of black gaffer's tape on the outside to make a backing, then Ultra Black on the inside. Remove the tape backing, or not, after the gasket maker dries, according to your preference. You made it just too easy. I will stop by the shop on the way home. TIP - or my two-bits worth. Gaffer's is too sticky for some masking jobs. 3M has "blue" masking tape. If you look on the side of the roll they have the stickiness factor from less to more sticky (1 to 5). I use #2 because it releases easily and doesn't take underlying paint or whatever off the surface. Highly recommended for small jobs. (Expensive stuff, too.) |
#14
|
|||
|
|||
Enlarger Bellows Rebuild - modern tricks?
In article ,
jjs jjs.jjs.net wrote: TIP - or my two-bits worth. Gaffer's is too sticky for some masking jobs. 3M has "blue" masking tape. If you look on the side of the roll they have the stickiness factor from less to more sticky (1 to 5). I use #2 because it releases easily and doesn't take underlying paint or whatever off the surface. Highly recommended for small jobs. (Expensive stuff, too.) I like that stuff. I use the black gaff tape on bellows because if the bellows is black, it generally matches well enough to not look too bad if left in place, it is easy to tear neatly to match the existing width of the bellows fold being fixed, and the adhesive _seems_ to not be acidic enough to eat the bellows material underneath and turn it to dust (though I have never left any in place longer than about 10 years, and that on a synthetic, not leather, bellows). It gives me some peace of mind lest the Permatex should come loose and the bellows suddenly leak light -- that won't happen, with the gaffer's tape on there. -- Thor Lancelot Simon "The inconsistency is startling, though admittedly, if consistency is to be abandoned or transcended, there is no problem." - Noam Chomsky |
#15
|
|||
|
|||
Enlarger Bellows Rebuild - modern tricks?
"Thor Lancelot Simon" wrote in message
... [... snip... we are discussing Gaffer's tape ...] dust (though I have never left any in place longer than about 10 years, Only ten years? I should start a separate thread on Gaffer's tape, but I'll risk comments here - I haven't found any that was the same as the stuff we used in the early Seventies. This is not a case of selective memory. The original stuff could be folded over on itself into a small square and stuck in the pocket for odd emergencies outside of work. It unfolded nicely without leaving residue in itself and would work again. At work they order some kind of no-name Gaffers equivalent but it is not even close. I have just a bit left of my last roll of Bogen's equivalent and it does not have the same release adhesive. It's the end of an era, I tell ya. Today I get funny looks from photography students if I mention Gaffer's. It's like they are thinking Cut, Paste and Lock Layer is the same. So, can you recommend a replacement for Bogen's? I suppose it's Manfrotto now. |
#16
|
|||
|
|||
Enlarger Bellows Rebuild - modern tricks?
... gaffer tape ... it's not like it used to be ...
"Gaffer Tape" (tm) is no longer. I haven't tried these, but it's probably the best that can be done. http://www.filmtools.com/ -- search for gaffer Things are not what they used to be, and they never were. -- Nicholas O. Lindan, Cleveland, Ohio Darkroom Automation: F-Stop Timers, Enlarging Meters http://www.darkroomautomation.com/index2.htm n o lindan at ix dot netcom dot com |
#17
|
|||
|
|||
Enlarger Bellows Rebuild - modern tricks?
"Nicholas O. Lindan" wrote in message
... http://www.filmtools.com/ -- search for gaffer Whoa! A new toy store! Thanks. I'll try their 2" tape. Just right for little jobs. Lookie he http://www.filmtools.com/dkzdse10moba.html Wonder if that would work for a custom-made 10x10" enlarging light box? Or should I start to use up the cases of Mazda 75 flashbulbs? Getting goofy. End of work day. 'nite |
#18
|
|||
|
|||
Enlarger Bellows Rebuild - modern tricks?
Pico wrote:
(. . .) I haven't found any that was the same as the stuff we used in the early Seventies. This is not a case of selective memory. The original stuff could be folded over on itself into a small square and stuck in the pocket for odd emergencies outside of work. It unfolded nicely without leaving residue in itself and would work again. (. . .) Sounds like what others of us in the same era referred to as "racing tape", suitable for body work, patching an exhaust manifold, or (rolled up) a (non-functioning) substitute for a spark plug. :-) |
|
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
A factory "rebuild" question | Larry | Digital Photography | 7 | November 15th 05 02:51 AM |
Broken Olypus C3030 zoom Lens unit rebuild instructions? | [email protected] | Digital Photography | 2 | November 27th 04 01:21 AM |
FS: 5x7 Bellows mfg by Western Bellows | Mike Long | Large Format Equipment For Sale | 0 | November 21st 04 05:43 PM |
shutter rebuild instructions | Matt Ashbrook | Large Format Photography Equipment | 13 | November 16th 04 01:29 AM |