If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
Negative Carriers
I just purchased a Fuji Model B enlarger, which (at a very reasonable
price) came without lenses or negative carriers. I have lenses in process -- M39 mount, so not hard to arrange, and "normal" lenses are quite reasonable these days (I'm not looking forward to paying for the 28 mm or shorter I'll want for 16 mm negatives, though). I can make negative carriers if I must, but if I could buy some used ones, I'd prefer it. Does anyone know if the Fuji Model B uses the same carriers as a common enlarger like a Durst, Omega, Beseler, Bogen, etc.? FWIW, it's a condenser type with a 6x9 cm maximum opening. -- I may be a scwewy wabbit, but I'm not going to Alcatwaz! -- E. J. Fudd, 1954 Donald Qualls, aka The Silent Observer Lathe Building Pages http://silent1.home.netcom.com/HomebuiltLathe.htm Speedway 7x12 Lathe Pages http://silent1.home.netcom.com/my7x12.htm Opinions expressed are my own -- take them for what they're worth and don't expect them to be perfect. |
#2
|
|||
|
|||
Negative Carriers
Many of the Japanese enlargers are similar to the Bogen, Spiratone, etc.
that were also imported from Japan in the 60's, 70's, 80's. They use stamped metal carriers made in either two parts with a simple hinge or a more complicated multi-part design. If you have no carriers you'll need to make measurements and describe the type and size carrier you need. Or you can take an existing carrier and mask down the opening with black tape for smaller sizes or get out the Dremel to enlarge to opening for bigger negs. With a little inspecting it shouldn't be that hard to fabricate all new carriers as well. I would recommend matt board scraps for the one off jobs where you have only a few negs of a size to print and for more permanent rigs-aluminum. Use flat black paint, Krylon's heat resistant black (made for Barbecue's works well) and have at it. -- darkroommike ---------- "Donald Qualls" wrote in message news:dAYoc.6809$6f5.558613@attbi_s54... I just purchased a Fuji Model B enlarger, which (at a very reasonable price) came without lenses or negative carriers. I have lenses in process -- M39 mount, so not hard to arrange, and "normal" lenses are quite reasonable these days (I'm not looking forward to paying for the 28 mm or shorter I'll want for 16 mm negatives, though). I can make negative carriers if I must, but if I could buy some used ones, I'd prefer it. Does anyone know if the Fuji Model B uses the same carriers as a common enlarger like a Durst, Omega, Beseler, Bogen, etc.? FWIW, it's a condenser type with a 6x9 cm maximum opening. -- I may be a scwewy wabbit, but I'm not going to Alcatwaz! -- E. J. Fudd, 1954 Donald Qualls, aka The Silent Observer Lathe Building Pages http://silent1.home.netcom.com/HomebuiltLathe.htm Speedway 7x12 Lathe Pages http://silent1.home.netcom.com/my7x12.htm Opinions expressed are my own -- take them for what they're worth and don't expect them to be perfect. |
#3
|
|||
|
|||
Negative Carriers
BTW small diameter plus diopter closeup lenses work well in a pinch
to modify the focal length of enlarging lenses. The Voss 28mm is pretty good, not too expensive, and has a recessed mount (Important if your enlarger does not have recessed lens boards.). -- darkroommike ---------- "Donald Qualls" wrote in message news:dAYoc.6809$6f5.558613@attbi_s54... I just purchased a Fuji Model B enlarger, which (at a very reasonable price) came without lenses or negative carriers. I have lenses in process -- M39 mount, so not hard to arrange, and "normal" lenses are quite reasonable these days (I'm not looking forward to paying for the 28 mm or shorter I'll want for 16 mm negatives, though). I can make negative carriers if I must, but if I could buy some used ones, I'd prefer it. Does anyone know if the Fuji Model B uses the same carriers as a common enlarger like a Durst, Omega, Beseler, Bogen, etc.? FWIW, it's a condenser type with a 6x9 cm maximum opening. -- I may be a scwewy wabbit, but I'm not going to Alcatwaz! -- E. J. Fudd, 1954 Donald Qualls, aka The Silent Observer Lathe Building Pages http://silent1.home.netcom.com/HomebuiltLathe.htm Speedway 7x12 Lathe Pages http://silent1.home.netcom.com/my7x12.htm Opinions expressed are my own -- take them for what they're worth and don't expect them to be perfect. |
#4
|
|||
|
|||
Negative Carriers
Mike King wrote:
Many of the Japanese enlargers are similar to the Bogen, Spiratone, etc. that were also imported from Japan in the 60's, 70's, 80's. They use stamped metal carriers made in either two parts with a simple hinge or a more complicated multi-part design. If you have no carriers you'll need to make measurements and describe the type and size carrier you need. Or you can take an existing carrier and mask down the opening with black tape for smaller sizes or get out the Dremel to enlarge to opening for bigger negs. With a little inspecting it shouldn't be that hard to fabricate all new carriers as well. I would recommend matt board scraps for the one off jobs where you have only a few negs of a size to print and for more permanent rigs-aluminum. Use flat black paint, Krylon's heat resistant black (made for Barbecue's works well) and have at it. Thanks, Mike. This one has a pair of simple leaf springs to hold the carrier in place under the condenser, so I'd expect the original carriers consisted of two flat plates, possibly with a film width milled slot for clearance and alignment pegs, of course, and likely some kind of flange around the outer edge to prevent fogging from stray light. Hinged or not, I don't know -- no carriers at all with it. The lower body has a tab protruding at the front of the carrier slot which has a threaded hole that looks like M5; I have no idea what for. The carrier stage is circular, almost exactly 150 mm diameter, with a chordal straight edge at the back 28 mm deep into the circle. There's a milled notch with a leaf spring in each end (secured by large headed screws that probably also acted as stops); the slot is 5 mm wide and 5 mm deep, in the head within the chordal rebate, about 3 mm behind the back of the stage proper, which I also haven't identified as to purpose, though it looks as if a 5 mm rod could be inserted from either end to a depth of about 35 mm. Minimum bellows length is 29 mm from the top of the M39 threads to the bottom surface of the negative carrier stage; 28 mm lens might work without modifcation, as long as I won't need huge magnifications. The condenser is about 115 x 80 mm, and the bottom of the condenser would be no more than about 6 mm from the negative, so it probably used glassless carriers. It looks as if this one might fit, at least by shape: http://cgi.ebay.com/ws/eBayISAPI.dll...5153 023&rd=1 It doesn't look as if any of the Beseler, Omega, or Saunders carriers listed on eBay will fit. I surely can fabricate carriers to fit (though I prefer brass over aluminum, because it can be soldered more easily) -- though it would be easier with one factory carrier to look at. It'd be still easier, though, to buy some, especially with the fire-sale prices on off-brand enlarging equipment on eBay these days. -- I may be a scwewy wabbit, but I'm not going to Alcatwaz! -- E. J. Fudd, 1954 Donald Qualls, aka The Silent Observer Lathe Building Pages http://silent1.home.netcom.com/HomebuiltLathe.htm Speedway 7x12 Lathe Pages http://silent1.home.netcom.com/my7x12.htm Opinions expressed are my own -- take them for what they're worth and don't expect them to be perfect. |
Thread Tools | |
Display Modes | |
|
|