A Photography forum. PhotoBanter.com

If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below.

Go Back   Home » PhotoBanter.com forum » Photo Equipment » Large Format Photography Equipment
Site Map Home Register Authors List Search Today's Posts Mark Forums Read Web Partners

MicroPress 4x5 question



 
 
Thread Tools Display Modes
  #21  
Old November 8th 07, 08:01 AM posted to rec.photo.equipment.large-format
murrayatuptowngallery
external usenet poster
 
Posts: 30
Default MicroPress 4x5 question

Flat lens boards on Graphics

I don't know if the flat board versions on the Graphics (Graphic View,
Mini Speed, etc), or even my Busch Pressman C have different front
standard light baffling than those with the stamped '3-D' bords.

The hassle I have had with flat board on my Crown Graphic has been
getting them the right size to fit under the board locks.

I made & gave someone a flat aluminum one, painted black, with rounded
corners doen on a belt sander, & he said he had no light leaks.

I had suggested an inner section of foam core. Many people make a '2-
step' flat one instead of the stamped deep ones.

The slide locks really irritated me with the flat boards. If you make
yourself replacement slide locks that are longer, you can run into the
opposite problem from the lens board not staying locked...difficult to
remove.

  #22  
Old November 8th 07, 12:12 PM posted to rec.photo.equipment.large-format
Richard Knoppow
external usenet poster
 
Posts: 751
Default MicroPress 4x5 question


"murrayatuptowngallery"
wrote in message
ups.com...
Flat lens boards on Graphics

I don't know if the flat board versions on the Graphics
(Graphic View,
Mini Speed, etc), or even my Busch Pressman C have
different front
standard light baffling than those with the stamped '3-D'
bords.

The hassle I have had with flat board on my Crown Graphic
has been
getting them the right size to fit under the board locks.

I made & gave someone a flat aluminum one, painted black,
with rounded
corners doen on a belt sander, & he said he had no light
leaks.

I had suggested an inner section of foam core. Many people
make a '2-
step' flat one instead of the stamped deep ones.

The slide locks really irritated me with the flat boards.
If you make
yourself replacement slide locks that are longer, you can
run into the
opposite problem from the lens board not staying
locked...difficult to
remove.


The Graphic View uses metal lens boards which are other
wise the same as the wooden ones for Anniversary Speed
Graphics. Well, there _is_ a difference. The wooden boards
are thick with a thiner border to fit the opening in the
camera. This provides a light trap. The metal boards have
constant thickness but have a raised boss around the holder
which fits into the front standard and provides the same
sort of light trap. However, the center of the board is
thinner so it can take some lenses with retaining rings or
the flange on the back that could not fit on a wood board
without undercutting.
For 4x5 cameras 4x4 inch boards of the Graphic wood type
will fit the Graphic View, the Burke & James press camera,
and the Calumet CC-400. However, the CC-400 boards will not
fit into the other cameras because it has a sliding lock on
both top and bottom and no taper on one edge. The lack of a
taper prevents the edge of the these boards from fitting
into the bottom of a Speed Graphic or Graphic view. Calumet
boards are flat, thin, and have a raised boss around the
edge but a much shallower one than the Graphic View board.
I think the rounded corners you mention must be for a
Pacemaker Graphic. These use a completly different design
made of stamped sheet metal with a bent down rim around the
edges. The rim forms a light trap. These boards will not fit
other cameras without an adaptor.


--
---
Richard Knoppow
Los Angeles, CA, USA



 




Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is Off
HTML code is Off
Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Good morning or good evening depending upon your location. I want to ask you the most important question of your life. Your joy or sorrow for all eternity depends upon your answer. The question is: Are you saved? It is not a question of how good Rôgêr Digital Photography 0 April 21st 05 03:32 PM


All times are GMT +1. The time now is 09:11 AM.


Powered by vBulletin® Version 3.6.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright ©2004-2024 PhotoBanter.com.
The comments are property of their posters.