If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
Olypus C-5050 Tripod Mount Screws
pc_whocares wrote:
Looking for source and specs for my C-5050 tripod mount in the bottom of the camera. The screws fell out (they aren't in the bag....) I used to work for Hughes and have an extraordinary selection of very small unified thread screws, (some will even CLEAR the threadded holes in the socket) but these appear to be METRIC. Can any of 'yall give me the screw specs and possibly a source? SHOULD be 1/4 - 20 .. not metric. -- -- r.p.e.35mm user resource: http://www.aliasimages.com/rpe35mmur.htm -- r.p.d.slr-systems: http://www.aliasimages.com/rpdslrsysur.htm -- [SI] gallery & rulz: http://www.pbase.com/shootin -- e-meil: Remove FreeLunch. -- usenet posts from gmail.com and googlemail.com are filtered out. |
#2
|
|||
|
|||
Olypus C-5050 Tripod Mount Screws
"Alan Browne" wrote in message ... pc_whocares wrote: Looking for source and specs for my C-5050 tripod mount in the bottom of the camera. The screws fell out (they aren't in the bag....) I used to work for Hughes and have an extraordinary selection of very small unified thread screws, (some will even CLEAR the threadded holes in the socket) but these appear to be METRIC. Can any of 'yall give me the screw specs and possibly a source? SHOULD be 1/4 - 20 .. not metric. I think the OP is talking about the set screws that hold the 1/4-20 flange to the chassis. |
#3
|
|||
|
|||
Olypus C-5050 Tripod Mount Screws
Spam This wrote:
"Alan Browne" wrote in message ... pc_whocares wrote: Looking for source and specs for my C-5050 tripod mount in the bottom of the camera. The screws fell out (they aren't in the bag....) I used to work for Hughes and have an extraordinary selection of very small unified thread screws, (some will even CLEAR the threadded holes in the socket) but these appear to be METRIC. Can any of 'yall give me the screw specs and possibly a source? SHOULD be 1/4 - 20 .. not metric. I think the OP is talking about the set screws that hold the 1/4-20 flange to the chassis. DOH! I see tripod mount and go into auto-reply. -- -- r.p.e.35mm user resource: http://www.aliasimages.com/rpe35mmur.htm -- r.p.d.slr-systems: http://www.aliasimages.com/rpdslrsysur.htm -- [SI] gallery & rulz: http://www.pbase.com/shootin -- e-meil: Remove FreeLunch. -- usenet posts from gmail.com and googlemail.com are filtered out. |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Tripod Mount at *End* of PowerShot! Why? | [email protected] | Digital Photography | 27 | January 18th 07 01:41 PM |
with or without tripod mount | rwesurfn | Digital SLR Cameras | 7 | January 13th 05 11:06 PM |
pentax lens mount screws stripped... | Glen A Stromquist | 35mm Photo Equipment | 0 | September 26th 04 04:12 PM |
tripod screws | TS | Other Photographic Equipment | 2 | August 9th 04 05:27 AM |
tripod screws | TS | Digital Photography | 4 | August 7th 04 06:56 PM |