If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
|
#1
|
|||
|
|||
The Curse of the Curl
Hello, all
I have at last got collected courage to digitize some of my old films which were processed in cheap photolabs and probably dried in a hurry. I have been storing them in rolls and now, after cutting them into strips I have been struck by the extent of lateral curl. My scanner won't just focus on such films, unless I use special film holder which is less convenient and also crops the frame by about 2 mm in heght and width. Do you have any suggestions as to how to flatten and old and heavily curled film (meaning alteral curl, from edge to edge). Thank you in advance, Anton |
#2
|
|||
|
|||
The Curse of the Curl
You might try higher humidity. It can take several days for
the film to flatten out. The other approach is to weigh it down flat. Put the film strips between the pages of a book and stack more books on top. The best solution, vis-à-vis r.p.d, is a glass carrier, an enlarger and a wet darkroom and make prints ... -- Nicholas O. Lindan, Cleveland, Ohio Darkroom Automation: F-Stop Timers, Enlarging Meters http://www.darkroomautomation.com/da-main.htm n o lindan at ix dot netcom dot com "Anton" wrote in message 09... old films which were processed in cheap photolabs ... storing them in rolls ... after cutting them into strips ... lateral curl ... [can't scan] |
#3
|
|||
|
|||
The Curse of the Curl
Thanks for the reply, Nicolas,
You might try higher humidity. It can take several days for the film to flatten out. Yes. Right now I am keeping it in a spiral container, wherein the film remains laterally flat, in the bath with a hot shower on. I was going to keep it that way for a while (so it absorbs enough water) and then to start reducing the water flow, step by step, to let the film dry slowly and uniformly, until I switch the water off. Then, hopefully, it will be properly dried and flat... The other approach is to weigh it down flat. Put the film strips between the pages of a book and stack more books on top. Just keeping them flat doen't help in my case. When I take the films back they get curl again as if nothing has been done. Some temperature and humidity conditions are probably also required. And can one keep a high humidity if the film is squeezed between pages of a book? But I do keep all my recent films under weight. In this regard, I got one more question: are transparent film sleevers suitable for long-term storage? Or do I need those made from acid-free papaer for that? The best solution, vis-?-vis r.p.d, is a glass carrier, an enlarger and a wet darkroom and make prints ... Yes, yes and yes. But I do want to scan them. And the colour process is way more difficult. Anton |
#4
|
|||
|
|||
The Curse of the Curl
You might try higher humidity. It can take several days for
the film to flatten out. Yes. Right now I am keeping it in a spiral container, wherein the film remains laterally flat, in the bath with a hot shower on. I was going to keep it that way for a while (so it absorbs enough water) and then to start reducing the water flow, step by step, to let the film dry slowly and uniformly, until I switch the water off. Then, hopefully, it will be properly dried and flat... After drying up the curl returned (( Will try keeping it in warm humid air for a longer time. Anton |
#5
|
|||
|
|||
The Curse of the Curl
On 2010-01-16 12:47:34 -0500, Anton said:
Hello, all I have at last got collected courage to digitize some of my old films which were processed in cheap photolabs and probably dried in a hurry. I have been storing them in rolls and now, after cutting them into strips I have been struck by the extent of lateral curl. My scanner won't just focus on such films, unless I use special film holder which is less convenient and also crops the frame by about 2 mm in heght and width. Do you have any suggestions as to how to flatten and old and heavily curled film (meaning alteral curl, from edge to edge). Thank you in advance, Anton One thing that sometimes works is to rewind the film emulsion side out and store it that way for a while. I know you are talking about edge to edge curl but reverse winding will oppose that also and may apply more torque over a longer time than other tricks, especially merely flattening it out, which does not over curl it in the other direction. -- Michael |
#6
|
|||
|
|||
The Curse of the Curl
Writing just to inform you about my progress. I loaded a strip into a spiral holder (emulsion side out) and let it soak water for about ten minutes. Then I poured some water on the bottom of the container and put the spiral holder with my strip into it, and sealed it. So it will re- main in a very moist environment for a day. Then I will unseal it and wait futher for film to dry. |
#7
|
|||
|
|||
The Curse of the Curl
On 1/20/2010 11:25 AM Anton Shepelev spake thus:
Writing just to inform you about my progress. I loaded a strip into a spiral holder (emulsion side out) and let it soak water for about ten minutes. Then I poured some water on the bottom of the container and put the spiral holder with my strip into it, and sealed it. So it will remain in a very moist environment for a day. Then I will unseal it and wait futher for film to dry. One question: are you planning on drying the film *on the reel*? I wonder if you don't risk having the film stick to the reel this way. -- You were wrong, and I'm man enough to admit it. - a Usenet "apology" |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
How to eliminate length-wise curl | Paul Moore | Digital Photography | 1 | February 11th 09 10:37 PM |
b/w negative curl | Ted Quackenbush via PhotoKB.com | In The Darkroom | 9 | April 1st 05 04:58 PM |
Negative curl... widthwise not lengthwise... | Jed Savage | In The Darkroom | 15 | December 6th 04 05:00 AM |
Controlling curl on FB paper | ? | In The Darkroom | 4 | February 17th 04 12:54 PM |